|
|
|
|
|
|
|
Signal Conditioning Solutions
New INSTRUMENT CLASS™ DIN Rail Mount 2-Wire Transmitter
Offers Industry's Highest Performance At Lowest Cost
Dataforth Corporation, Tucson,
Arizona announces the introduction of its new DSCT series of loop powered two-wire
transmitters. Seven family groups provide 49 transmitter models that interface
to a wide variety of voltage, current, temperature and position measuring devices.
The DSCT is the latest introduction of Instrument Class™ products available
from Dataforth, which provide superior specifications such as ±0.03% accuracy,
five or six poles of filtering, 1500Vrms continuous isolation, low output noise,
and much more.
The DSCT two-wire transmitter
conditions and sends analog signals from sensors located in the "field" to monitoring
and control equipment, usually computers, located thousands of feet away in central
control areas. The DSCT accepts a wide range of inputs, including millivolt, volt,
milliamp, thermocouple, RTD, potentiometer, and slidewire. It operates on power
from a 2-wire signal loop and modulates the supply current to represent the input
signal within a 4 to 20 milliamp range.
|
|
|
|
|
Two-wire transmission loops
are very economical methods for connecting sensors to distant control rooms. Since
the DSCT operates from the signal loop current, no additional, expensive power
and wiring are required. Only low cost, twisted pair wiring is needed.
The DSCT employs a proprietary
isolation barrier to isolate the sensor signal from the current loop, eliminating
ground loops, permitting the grounding of both the sensor and the receiver, and
protecting valuable control equipment from damage due to field power surges and
lightning strikes. The transmitted 4 to 20mA signal is also virtually immune to
noise pick-up and interference and is independent of any resistance in the loop
wires. This combination of conditioning and transmission results in greater signal
integrity and protection of system investment. Appropriate certification approvals
are in process to allow operation in hazardous locations.
The Instrument Class™
DSCT product beats the competition in every significant performance category as
the following technical specifications illustrate:
- higher common mode rejection, 160dB, eliminates common mode voltage noise;
- three times the accuracy, ±0.03% typical compared to ±0.1 to 1.1% for other designs;
- improved linearity, ±0.01% typical compared to ±0.03 to 0.1%;
- temperature linearization using up to nine breakpoints provides conformity to ±0.05% verses up to ±0.30% for other designs;
- much lower output noise, 3µArms compared with 16 to 80µArms;
- 5 poles of filtering result in 85dB attenuation at 60Hz compared with 35 to 60dB;
- 1500Vrms continuous isolation compared with 100 to 1000VDC;
- very wide range loop supply voltage from 10.8VDC minimum to 100VDC maximum allows use in any current loop.
- fully protected output, i.e. continuous protection against reverse connection of loop voltage, overvoltage, accidental connection of up to 240VAC sustained, and transients (ref. ANSI/IEEE C37.90-1989);
- fully protected inputs, i.e. continuous protection against overvoltage, transients, and accidental connection of up to 240VAC sustained;
- high input impedance, >50MW compared with 1 to 10MW for other designs, of particular importance when interfacing to high impedance sensors.
Operation and storage temperature
is -40°C to +80°C, and relative humidity range is zero to 95% noncondensing. All
models meet the requirements of EN50081-1 (radiated/conducted emissions) and EN50082-1
(ESD/RF/EFT immunity).
The DSCT is packaged in
a rugged thermoplastic DIN rail mountable case with dimensions of 2.95 x 0.89
x 4.13 inches (75mm x 22.5mm x 105mm). This material provides excellent impact
properties, dimensional stability over temperature, chemical resistance and has
a flammability rating of V-0. For ease of system assembly and reconfiguration,
all signal lines are secured to the module using screw terminals integral with
pluggable terminal blocks. These terminal blocks are equipped with pull-tabs,
which also function as protective covers for the screw terminals. The modules
may be mounted on standard DIN EN50022-35x7.5 or -35x15 rails.
Dataforth Corporation was
established in 1984 and is a worldwide leader in the design and manufacture of
signal conditioning and data communications products for industrial and institutional
markets. The Company offers a broad range of analog and digital I/O modules, two-wire
transmitters, industrial data modems, and modem systems.
Go
directly to our DSCT family in our
Signal Conditioning Products Catalog.
Data acquisition. Signal conditioning. Signal conditioners. Thermocouple.
Strain gage. Data loggers. Data logging. PC-based data acquisition.
5B signal conditioning. Dataforth provides all data acquisition and
signal conditioning solutions.
|
|
|
|
|
